Nova 55175 Gebrauchs- und Pflegehandbuch

115-0513-003 1 NOVA DVR XP TM (Xtra Performance) WOODLATHE Publication 115-0513-003 IN S T R U C T I O N MA N U A L

115-0513-003 10 Setting Up Your Workshop Workshop Requirements Consideration Recommendation L

115-0513-003 11Example of Shop-made Lathe Stand This has been designed with economy of space in mind. Heavier sections, wider rails and gussets on th

115-0513-003 12 Assembling the Nova DVR XP 1. Unpack the lathe and components from the shippin

115-0513-003 13Installing the Headstock Lockpin 3. Remove the plastic shipping tube from headstock base. Immediately screw the Headstock Lockpin

115-0513-003 14 with the wrench from the bottom of the bed. ! Warning! Do not use a metal

115-0513-003 15Mounting the Lathe to a Support Surface 1. Place the lathe on the stand top. Locate the front and left corner of the lathe approxim

115-0513-003 16 Using the Nova DVR XP Parts of the Nova DVR XP Woodlathe DVR Variable Speed

115-0513-003 17DVR Drive Functions A two-string liquid-crystal display panel (LCD) displays the current information. Ready to start at XXXXrp

115-0513-003 18 The Direction of rotation setting is only available in the ready to start mode.

115-0513-003 19Turning Tips The Nova DVR XP drive technology is not just a variable speed motor -its smart motor technology takes turning to a new l

2 115-0513-003 Models 1)55175 spindle thread 1 1/4" x 8 tpi 115v 2) 55180 spi

115-0513-003 20 Swiveling the Headstock 1. Stop the lathe. Insert the operating bar into a hol

115-0513-003 21Headstock The headstock houses the Rotor, Stator, Electronics, bearings, and the Spindle. The headstock spindle accepts centers and ac

115-0513-003 22 Using a spur center Mount the spur center to the work piece a

115-0513-003 23Lathe Turning speeds Correct selection of turning speeds is important for safety and finish cut quality It is important to take into

115-0513-003 24 Learning Turning The art and technique of turning is a subject beyond the scope

115-0513-003 25 CONTROLLER USER’S GUIDE NOVA DVR (SWITCHED RELUCTANCE) DRIVE Control Software versions 4.54x Interface Software version s03 Teknatool

115-0513-003 26 3.0 HUMAN MACHINE INTERFACE DESCRIPTION The Human Machine Interface (HMI) prov

115-0513-003 27 4.0 CONTROL FUNCTIONS Drive Parameter Settings (Set Function) HMI display lines contain the parameters, which can be edited. Press

115-0513-003 28 5.0 CONTROL OPERATIONS AT STOP MODE 5.1 Starting operation Insert the drive

115-0513-003 295.2 Reference speed setting. Preset (favorite) speed selection and set function There are 5 preset speeds available in the drive. T

115-0513-003 3 Solid Construction Well proven design, the Nova DVR XP is made from Cast Iron com

115-0513-003 30 • Pick a preset number you would like to change. IMPORTANT Note: The default

115-0513-003 315.4 The Speed Control Loop. The PI Speed Control coefficients setting The control system of the DVR Drive has Speed Control Loo

115-0513-003 32 5.5 Serial Number view. • Press PROGRAMP (“Page”) again to see Board Serial

115-0513-003 33Maintaining the Nova DVR3000 General Maintenance Always isolate from power supply (unplug) before carrying out any maintenance Int

115-0513-003 34 Cleaning the Toolslide If the toolslide becomes hard to move and adjust, clea

115-0513-003 35Aligning the Tailstock 1. Crank the Handwheel back so the quill is all the way in. 2. Place any #2 MT accessories you have that h

115-0513-003 36 Voltage selection By removing a small jumper the unit will efficiently run on 2

115-0513-003 37 5. Carefully place your index finger on the edge of the board avoiding any soldier points. Using the top of your finger as a guide r

115-0513-003 38 Troubleshooting Guide Problem Possible Cause and Solution Excessive vibration.

115-0513-003 39Display screen shows Press off button; switch off computer by master switch wait one minute and switch on again. Check that the spind

4 115-0513-003 Welcome Thank you for choosing our Nova DVR XP Woodlathe and welcom

115-0513-003 40 Troubleshooting Guide continued Problem Possible Cause and Solution Tailstock

115-0513-003 41DVR XP Woodlathe Parts List Item # Qty Part # Description 1 1 55048 Lock Pin 2 1 24118

115-0513-003 42 Item # Qty Part # Description 50 1 55012 Swivel Pin-Headstock 51 1 55145 H

115-0701-001 - 43 -

115-0701-001 - 44 - Accessories Add On Bed Extension: 55195 Extend the bed of your Nova DVR XP Woodlathe for greater capacity for turning between

115-0513-003 45Accessories Faceplates: SFP80L (with side-locking function). Faceplates are used to mount the work piece when faceplate turning bowls

115-0513-003 46 Index Accessories 42,43 Assembling 11 Bed - Lathe 2, 3, 9, 13, 14, 21, 22, 23,

115-0513-003 47 Teknatool Warranty Teknatool Five Year Limited Warranty ( 2 year on electrical parts) This Teknatool product is backed by a warrant

115-0513-003 48 Steps to registering your Warranty by Mail: 1. Fill out the information on pag

115-0513-003 49

115-0513-003 5 Contact NOVA New Zealand and Rest of the World Teknatool International Ltd Phon

115-0513-003 50 Nova DVR XP Woodlathe Manual Publication Code: 115-0701-001 © Teknatool Int

6 115-0513-003 Table of Contents GENERAL SAFETY RULES ...

115-0513-003 7The information and specifications contained herein are subject to change. Teknatool is not responsible for errors or omissions herein

115-0513-003 8 ADDITIONAL SAFETY RULES FOR WOODLATHES ! Warning! Failure to follow these rule

115-0513-003 9 DVR XP Woodlathe Specifications Size: 1100mm(L) x 240mm (W) x 412mm(H) 43 1/3"(L) x 9 1/2" (W) x 16 1/4"(H) Weig